У меня HTC Wizard на том же процессоре TI850. Могу сдуть процессор и вызвонить куда идут ноги.....но вот откуда слить бут....И ещё disconchip шить читать каким нить програматором можно?

А что именно непонятно, если начсет МТТУ, то отключи в актив синк, снь галочку с "разрешить ЮСБ подключения",потом загоняеш тел в бут, и зпускаеш МТТУ, нажимаеш ЮСБ, ну и вводиш в нем ? или h, и он покажет тебе список доступных команд, посмотри на ХДА, тм должен быть список и их назначение

Вот приблизительный список и расшифровка, но для каждого бута и девайса эти параметры могут меняться это для тайфуна:
mb [StartAddr [Count [Filler]]]-Display/Set memory content. StartAddr can be either a hex_address or a register name When StartAddr is not given, memory display continues from the previous address. When Count is not given, previous Count is used for memory display Count is initially set to 20 (hex). If Filler is specified, the memory area is filled with Filler. Memory will be displayed/counted as bytesStartAddr must be in valid unmapped space. It is not validated.
mh [StartAddr [Count [Filler]]]-Display/Set memory content. StartAddr can be either a hex_address or a register name When StartAddr is not given, memory display continues from the previous address. When Count is not given, previous Count is used for memory display Count is initially set to 20 (hex). If Filler is specified, the memory area is filled with Filler. Memory will be displayed/counted as half-words StartAddr must be in valid unmapped space. It is not validated.
mw [StartAddr [Count [Filler]]]-Display/Set memory content. StartAddr can be either a hex_address or a register name When StartAddr is not given, memory display continues from the previous address. When Count is not given, previous Count is used for memory display Count is initially set to 20 (hex). If Filler is specified, the memory area is filled with Filler. Memory will be displayed/counted as words StartAddr must be in valid unmapped space. It is not validated.
ppdl [pathname]- Download the BIN file that assigned by PPSH command line. This download is via parallel port
flashtest-Test Flash.
l [pathname]- Download the BIN file via MTTY.
lr [pathname]- Download bin file and run

tftp- Download the BIN file via TFTP.
r2sd (ipl/spl/splash/os/gsm/ffs/all/gsmdata/diag)- r2sd (ipl/spl/splash/os/gsm/ffs/all/gsmdata/diag) Backup DOC image to SD card .
map- Display virtual address mapping table
timer- Test Timer
jump- Jump to address and execute
flashtype 0 (or 1)- Set Flash Type: 0:NOR ;1OC.
rdoc PartitionType- Read DOC: rdoc PartitionType PartitionType: 0 (IPL) PartitionType: 1 (SPL) PartitionType: 2 (XIPKERNEL) PartitionType: 3 (BINFS) PartitionType: 4 (FATFS) PartitionType: 5 (GSM DATA) PartitionType: 6 (GSM CODE)
wmac- The Format should be like this :wmac 0010 B5E4 3CC6 5 0010 B5E4 3CC6 : the MAC address 5: the max time to wait for dynamic IP form DHCP server
rmac- Read MAC address of Ethernet Controller from EEPROM
uart- Onboard serial port testing
debug- debug sub commanddebug keypad, debug led, debug vibrator, debug keyled, debug frontlight, debug flashlight, debug sir, debug spi, debug audio, debug syren, debug 13m, debug a7, debug dsp, debug battery, debug speak, debug csmixpanel, debug setbt, debug setdai, atcmd keypad
SetKeypad
SetKeypad 1(Typhoon)/2(Feelers)/3(Amadeus)/4(Sonata)
display-Epson Graphic Chip Display test
enteros-Enter OS
bininfo- Get Binary PartitionInfo of DOC

Сообщение отредактировал SAXON13 - 24.1.2009, 12:41