Eten M700 Jtag pinout table.

plase help me.

my jtag wiggler jtag.
My english bad sorry my turkish

Do you need JTAG points? Or something else?

yes, i do
please send me pinout picture

how to eten jtag connection prosedur ?

1. wiggler jtag (3.2 volt) adapter connect
2. connect to jtag cable eten mainboard
(TCK,TMS,TDO,TDI,GND)
3. eten m700 reset button

(right or wrong)
????????????????????????
Plase help me

Thank you old kind madmike

plase help meee

Eten M700 mainboard image.
(TDO,TCK,TDI,TMS,GND,RST)
?????

see this topic: http://forum.pda2u.ru/forum/topic295.html?view=findpost&p=5646
may be it is same one

Yes, it is the same one!

Thank You.

try to jtag, after news

my english speak bad. sorry.

i am write to forum and you delete (IMG:http://forum.pda2u.ru/style_emoticons/default/smile.gif)
now am i can write to forum

Sorry.

1. connection adapter to jtag (3.7 volt)
2. connection jtag cable to eten m700 and lpt port.
3. connection adapter to eten m700 on power
4. reset eten m700
5. tdo signal 0 and 1

right or wrong ?

+------------------------------------+
| SEC JTAG FLASH(SJF) v 0.2 |
| (S3C2440X & SMDK2440 B/D) |
| for WIGGLER JTAG Dongle |
| Modified by Zibi 2008-03-31 |
| for GPS_MODEL_17_S_V1 Board |
+------------------------------------+

Usage: SJF2440 /f:<filename> /d=<delay>
ERROR: No CPU is detected(ID=0xebaafd73).

[SJF Main Menu]
0:K9S1208 prog 1:K9F5608 prog 2:28F128J3A prog
4:Memory Rd/Wr 5:Exit
Select the function to test:0

[K9S1208 NAND Flash JTAG Programmer]
ERROR: K9S1208 is not detected. Detected ID=0xB71F.

1.check connection between jtag cable from eten m700 to lpt port, and check is right connected
2.max length of jtag cable ~30 santimeters, what kind of jtag cable are you using is it have right schematic
if you doo all right, the CPU must be detected

wright the complete specification of your device, what kind of CPU and FLASH-chip

Thanx You. Saxon13

My cpu SC32442 (K9S1208)

My Jtag Wiggler jtag circuit. (basic jtag)


Port DB25: Conector JTAG:
------------ --------------
3 Resistencia 100 ohm Línea TMS
4 Resistencia 100 ohm Línea TCK
5 Resistencia 100 ohm Línea TDI
11 Resistencia 330 ohm Línea TDO
25 Línea Gnd
8-15 (puente)

and jtag modified wiggler circuit

My jtag cable 15 cm.
3 battery (3x1.5 volt) = 4.5 volt
eten mainboard trst none

_________________________________________________________________________
Eten web form write, i am not understand

connection presodure

( On cable nid in 1 state voltage -3.3 v.

eten mainboard circuit nid check state.

In power connect state on jtag pin (mainboard) (on m600+) TDI,TCK,TMS state 1.
In power on (end RST set in 1 -this is m600) state on mainboard pin setted in 0)

what is connection presodure

_________________________________________________________________________
wiggler circuit image and schmatic:

Follow this topic, it is about your CPU & how to work with it...(ATTENTION!!! dont use IPLSPL1.04.zip it is not for you device) http://forum.pda2u.ru/forum/topic298s0.html?p=4576&#entry4576
In the settings check right connection between pin-points & LPT
Try to detect CPU with utilite http://forum.pda2u.ru/forum/ipb.html?act=attach&...post&id=256

http://forum.pda2u.ru/forum/uploads//monthly_05_...81434_thumb.jpg

Сообщение отредактировал SAXON13 - 23.7.2008, 12:23

Thank you.

i am SC32442 jtag circuit completed.

now test. but error: (IMG:http://forum.pda2u.ru/style_emoticons/default/sad.gif)

+------------------------------------+
| SEC JTAG FLASH(SJF) v 0.1 |
| (S3C2442X & SMDK2442 B/D) |
+------------------------------------+
Usage: SJF /f:<filename> /d=<delay>
ERROR: No CPU is detected(ID=0xFFFDD3FF).

[SJF Main Menu]
0:K9S1208 prog 1:K9F5608 prog 2:28F128J3A prog
4:Memory Rd/Wr 5:Exit
Select the function to test:0

[K9S1208 NAND Flash JTAG Programmer]
ERROR: K9S1208 is not detected. Detected ID=0xFFD3.

Hi;

h-jtag program run, CORTEX-M3 select and noice program run.

'-------------------------------------------------------------------------------------------------------
C:\Program Files\NoICE\bin\NoICEARM.exe version 9.0.0.1900 product version 9.0.0.1900
NoICEARM - NoICE for ARM
John Hartman / Copyright © 1997-2008 by John Hartman
NOT REGISTERED. 29 days remain

Loaded RDI DLL C:\Program Files\H-JTAG\H-JTAG.dll
H-JTAG Debug Interface for ARM In-Circuit Emulation.
Version 1.50
Module 1) ARM CORTEX-M3
WinRDI Controller Capabilities 0x9B75A0:
WinRDI Target Capabilities: 0xC7:0xFF CallEx RT TX Synch
Target Info 0x219010: Thumb DCC NonStop
Watchpoint Info 0x0:
SingleStep: 0x4
Selected Target: Generic big-endian ARM using software breakpoints
Has 2 hardware breakpoints
Has software breakpoints

Target type ARM. Target buffer 128 bytes
Breakpoint instruction: BE 00
'------------------------------------------------------------------------------------------------------------

and file select load, selection *.bin file and address or offset 0x00000000
upload completed. and eten m700 dead

help me pls (IMG:http://forum.pda2u.ru/style_emoticons/default/smile.gif)