One man from XFU have a bricked Atom Life. Look for decision here.

Step 1. JTAG points discovery.
Need: detail foto the PCB (motherboad) with both side.

Step 2. Hardware preparation. Make a JTAG interface, for example very simple Xilinx or better Wiggler (download attached scheme from this post: http://forum.pda2u.ru/forum/index.php?showtopic=...ost&p=4988)

Step 3. Software preparation.
Need: - Bootloader for this device; - full damp from working device (optionally).
Download h-jtag from .www.hjtag.com.

Step 4. Software tools. Atom Life has PXA270 with a DOC. What I think jFlashMM will do.

It was return message when i use jflashmm as follow:
D:\Flame\ATOM EXEC JTAG\RepairBootLoader(EXEC)\JFlash_MM>jflashmm pxa27x32 ebo_
.nb0 N 0 PAR

JFLASH Version 5.01.007
COPYRIGHT © 2000 - 2003 Intel Corporation

PLATFORM SELECTION:
Processor= PXA27x
Development System= Mainstone
Data Version= 1.00.001

PXA27x revision ??
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 4 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 3 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 2 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 1 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_f000_2_32.dat

This program supports flash devices defined by DAT files
contained in the same directory as the executable program.

If the file cannot be opened, there are four possibilities:

1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
constructed filename. The first numeric value in the
filename is the device ID. Verify this value with the
component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
devices. Make sure that you are using the correct
platform data file.



any advise?thanks

afeng11,
Please try connect to PCB via H-JTAG. Lay out the screenshot and foto your PCB with jtag testpoints.

ok,i'll have a try then attach some photo here

this is the pic of atom life,where are the jtag points?thanks!

You know where there are test points? If is not present, lay out somewhere a photo of a deviceboard from both sides and give to our the link.

I am dead certain what recovery metod same with Atom Exec.
Please read and do more attentive manual, post http://forum.xda-developers.com/showthread.php?t=336278
Big Foto testpoints: http://forum.pda2u.ru/forum/index.php?showtopic=286

Please re-check your operate. Try connect into internals testpoint (on opposite side board)
Good Luck!

points were here,but which one was the jtag points?

Check an ohmmeter contacts nearby sim-holder and contacts on a PCB back side. Those that will be called on 99 % and there are points JTAG.

I have cleaned the topic from HTC Hurricane discussion.

can anyboby tell me the jtag contact of atom lif?thanks

i think, jtag contacts is similar with jtag atom exec.
jtag contacts near SIM connector is similar.
But.... Problem.
May be
May be Atom Life Need flashing MDOC.
If this theory is true, then...
Program for flashing not tested.
Program for flashing work in Linux only.


i think jtag is similar.

 JTAG_rover_orsio.jpg ( 93.75 килобайт ) Кол-во скачиваний: 108

I am sure jtag contacts is similar with jtag atom exec。
But the program can't flash the mdoc

По англицки не умею...
Но мне кажеца, что Jflash определяет только флэш-микросхемы производства Intel, т.к.
1) так написано в файлах самой программы
2) если просмотреть .dat файлы через блокнот то можно увидеть, что во всех есть строка типа 28F128L30B /* Designation for this memory type */, а 28F128L30B и все остальные описаные в других .dat файлах - это маркировка флэши производства Intel

english,please,i can't read any russia

Jflash supports flash-IC only manufactures Intel. That it has begun Flash MDoC, it is necessary corresponding .dat a file.

Online translate (IMG:http://forum.pda2u.ru/style_emoticons/default/dry.gif)

you mean there is no way to JTAG the Atom Life?
cuz I have Atom Life with dead bootloader and when I try ro Jtag I got some errors and I send a pic to you :

(IMG:http://www.tinypic.info/files/ei1hi6aq2cnc7irqlvws.jpg)

maybe you guys can help us to JTAG Atom life
I don't know....
anyway please just tell me is there anything else left that we could count on it to restore bootloader?
I see alex_beda said that it maybe work in linux, how can I run this software in linux?

this is the picture of my PPC:
(IMG:http://www.tinypic.info/files/6qnpyw709dxih7oiiibo.jpg)

Anyone solved it

O2 XDA Atom Life прошивался с miniSD во время прошивки появились ХХХХХХХ как я понял капец. В bootloader не заходит на нажатие любых вариантов кнопок не реагирует.Поможетли реанимация через JTAG под Windows.Какую прошивку ставить? (IMG:http://forum.pda2u.ru/style_emoticons/default/blink.gif) Зарание Спасибо за ответ. С Уважением Prado!

Парни помогите ожевить G6, Имел неостарожность BOOT стереть. Есть кабель J-TAG с помощью которого я оживлял HP 6815, но схемы для Ровера нет. И батареику на долго вынимал, и на кнопки жал , в различных комб. Только светодиод иногда мигает, и все. Может кто владеет даром воскрешенья зверьков? Помогите пожалуйста!!!!!!!!!!!!!!!!!!!! (IMG:http://forum.pda2u.ru/style_emoticons/default/laugh.gif)